• How do I know when to replace my Trimmer blade?
   
• How do I know when my pinion gears are worn?
   
• How do I know when my bearing is worn?
   
• How do I know when my 1000 Series II housing is worn?

• How do I adjust my Trimmer blade housing?
   
• What is the benefit of the new split housing?
   
• How do I set the depth gauge on my Series II Trimmer?
   
• How do I replace the bearing in my Series II Trimmer?
   
• What causes the frame to wear prematurely?
   
• Does Bettcher offer a tool to make proper Series II housing adjustments?

• What daily maintenance is needed for Series II Trimmers?
   
• How do I establish a regular maintenance program for my Whizard® Trimmers?
   
• How do extend parts life on my Series II Trimmer?

• What handle sizes are available for Series II Trimmers?

• How do I steel my small Trimmer blades?

• How do I steel my large Trimmer blades?

• How do I sharpen my Trimmer blades?

• My Trimmer handpieces are overheating, what can I do to correct the problem?

• My Trimmer handpieces are vibrating, what can I do to correct the problem?
   
• My Trimmer began to shutter from fat build-up while operating on the line.  Is there something I can do quickly to solve the problem without leaving the line?
   
• How do I properly clean my Whizard® Trimmers?
   
• What cleaner can I use to clean my Series II tools?
   
• Our current cleaning method is damaging the finish on our tools. Is there a better method?
   
• I would like to upgrade to Series II Trimmers. Does Bettcher offer a trade-in program?
   
• What do I use to lubricate my Whizard® Trimmers?
   
• How do I keep my 1000 Series II Trimmer running at peak performance?

• How do I sharpen my TrimVac™ AMX blade?
   

• Can I sharpen my TrimVac™ AMX blade on my 210 Sharpener?
   

• What happens to the air motor without proper lubrication?
   

• What cleaner can I use to clean my TrimVac™ tools?

Flex Shafts and DuraLite^® Casings

• How do I install a Flex Shaft and DuraLite^® Casing?
   

• How do I install a quick disconnect casing?
   

• How do I lubricate the flex shaft?
   

• Is there a non-aerosol form of WhizLube^™ available?
   

• How do I know when to replace the flex shaft and casing?
   

• How do I change the flex shaft motor adapter?
   

• How do I store my Flex Shafts and DuraLite^® Casings?
   

• How do I replace a Series II driver assembly?
   

• What do I use to lubricate my flex shafts?

• What maintenance is needed for the drive belt?
   

• How do I properly install my UltraDrive™ motor?
   

• How do I know when my drive adapter is worn?
   

• How do I change the motor adapter and disconnect assembly?
   

• How can I hang my motors more securely?
   

• How do I clean my UltraDrive™ motor?
   

• What is the part number for the new UltraDrive™ hanger peg?

UN-84 Motor

• How do I change the motor adapter and disconnect assembly?
   

• How do I install the new UN-84 Limit Switch?
   

• How do I install AutoEdge™ blade holders?
   

• Is there a special adjustment for the model 360 blade?
   

• How do I clean my AutoEdge™ Sharpener?
   

• How do I clean my grinding wheel?
   

• How do I troubleshoot the grinding motor?
   

• How do I replace the steeling device?
   

• Can I replace the solenoid cable on my AutoEdge™?
   

• How do I know when my grinding wheel is worn?
   

• How do I order an AutoEdge™ Bumper Kit?
   

• How do I perform general maintenance on my AutoEdge™?

• How do I lubricate my AirShirz®?
   

• What do I use to lubricate my AirShirz®?
   

• How do I remove the blade set from my AirShirz®?
   

• How do I adjust the finger loop post screw?
   

• How do I adjust smoothness and stroke on my AirShirz®?
   

• Is a left-handed AirShirz® available?
   

• Is an AirShirz® tool kit available?
   

• What is the proper air supply for AirShirz®?
   

• I need a new FRL unit for my tool. What do I need to order?
   

• How do I know when it's time to replace the air line filter?
   

• My AirShirz® is not running properly, what should I check?
   

• My tool does not have enough air pressure, how do I check the air supply?
   

• What cleaner can I use to clean my AirShirz® tools?
   

• How can I prevent users from adjusting the air control valves?

• Can I have the grinding wheel re-coated?

Miscellaneous - Food Processing

• What does my tool area need for proper tool maintenance?
   

• Do I need a return authorization number to return a piece of equipment?
   

• Can I send parts back to Bettcher Industries, Inc. for factory refurbishment?